久盛工業股份有限公司 Johnson Chemical Products Co., Ltd

規格&物性表

規格表

General Use Oil Seal（CPL General Curing）
Physical properties	Units	GS-592		GS-595
Hardness	Shore A	92 ±2		94 ±2
Hardness	Shore D	40		44
Density	g / cm3	1.18		1.18
Tensile strength	Kg / cm2	470		510
Elongation at break	％	500		500
100％Tensile modulus	g / cm3	95		120
Tear strength（Die C）	Kg / cm	140		150
Abrasion loss	mg	25		35
Compression set at room temperature	％	25		25
Compression set at 70oC x 24 hrs	％	< 35		< 35
Rebound resilience	％	50		40
Freezing temperature	oC	- 40		- 40
Vicat softening temperatur（1Kg）	oC	130		140
100oC x 70 hrs in ASTM oil＃1				Change
Hardness Shore	A	- 1		- 1
Tensile Strength	％	+ 5		- 4.3
Volume	％	0		- 0.3
100oC x 70 hrs in ASTM oil＃3
Hardness	Shore A	- 2		- 2
Tensile Strength	％	+ 6		- 0.1
Volume	％	+ 9		+ 8
In Air 120oC	Day	10	20	30	40
Tensile Strength	％	- 4	- 2	- 10	- 10

High Performing Use Oil Seal（HQEE Curing）
Physical properties	Units	HS 93
Hardness	Shore A	93 ± 2
Hardness	Shore D	43 ± 3
Density	g / cm3	1.2
Tensile strength	Kg / cm2	400
Elongation at break	％	500
100％Tensile modulus	g / cm3	120
300％Tensile modulus	g / cm3	220
Tear strength（Die C）	Kg / cm	130
Abrasion loss（H-22，1000mg，1000 cycles）	mg	23
Compression set at room temperature	％	22
Compression set at 70oC x 24 hrs	％	< 25
Compression set at 80oC x 70 hrs	％	< 30
Rebound resilience	％	55
Freezing temperature	oC	- 45
Vicat softening temperature（1Kg）	oC	150 - 160
100oC x 70 hrs in ASTM oil＃1		Change
Hardness	Shore A	0 / -1
Tensile Strength	％	+ 20
Volume	％	0
100oC x 70 hrs in ASTM oil＃3
Hardness	Shore A	- 2
Tensile Strength	％	+ 10
Volume	％	+ 8
In Air 120oC	Day	10	20	30	40
Tensile Strength	％	+10	0	0	-4

Size (in mm) of the Small Section of Small to Medium Seals ( UHS Type )
UHS	ID.	OD.	H
11.2	11.2	19.2	5
14	14	22	5
16	16	24	5
18	18	26	5
20	20	28	5
22.4	22.4	30	5
23.5	23.5	31.5	5
25	25	33	5
28	28	35.5	5
30	30	40	6
31.5	31.5	41.5	6
35	35	45	6
35.5	35.5	45	6
38	38	48	6
40	40	50	6
45A	45A	56	6
45	45	56	7
50	50	60	6
53	53	63	6
55	55	65	6
56	56	66	6
58	58	68	6
60A	60A	70	6
60	60	71	7
63	63	73	6
65	65	75	6
67	67	77	6
70	70	80	6
71	71	80	6
75	75	85	6
80	80	90	6
85	85	100	9
90	90	105	9
95	95	110	9
98	98	112	9
100	100	115	9
112	112	125	9
125	125	140	9
136	136	150	9
140	140	155	9
145	145	160	9
150	150	165	9
155	155	170	9
160	160	175	9
165	165	180	9
170	170	185	9
175	175	190	9
180	180	200	12
185	185	205	12
190	190	210	12
195	195	215	12
200	200	220	12

Size (in mm) of the Large Section of Small to Medium Seals ( DH Type )
DH	ID.	OD.	H1/H2
11.2	11.2	19.2	4.5/6
14	14	22	4.5/6
16	16	24	4.5/6
18	18	26	4.5/6
20	20	28	4.5/6
22.4	22.4	30.4	4.5/6
23.5	23.5	31.5	4.5/6
25	25	33	4.5/6
28	28	36	4.5/6
30	30	38	5/6.5
31.5	31.5	39.5	5/6.5
32	32	40	5/6.5
35	35	43	5/6.5
35.5	35.5	43.5	5/6.5
38	38	46	5/6.5
40	40	48	5/6.5
45	45	53	5/6.5
50	50	58	5/6.5
53	53	61	5/6.5
55	55	63	5/6.5
56	56	64	5/6.5
60	60	68	5/6.5
63	63	71	5/6.5
65	65	73	5/6.5
67	67	75	5/6.5
70	70	80	6/8.0
71	71	81	6/8.0
75	75	85	6/8.0
80	80	90	6/8.0
85	85	95	6/8.0
90	90	100	6/8.0
98	98	108	6/8.0
100	100	110	6/8.0
112	112	122	6/8.0
125	125	138	7/9.5
136	120	149	7/9.5
140	140	153	7/9.5
145	145	158	7/9.5
160	160	174	7/9.5

Size (in mm) of the Large Section of Small to Medium Seals ( UNS Type )
UNS	ID.	OD.	H
6.3	6.3	16.3	8
7.1	7.1	17.1	8
8	8	18	8
9	9	19	8
10	10	20	8
11.2	11.2	21.2	8
12.5	12.5	22.5	8
14	14	24	8
15	15	25	8
16	16	26	8
18	18	28	8
20	20	30	8
22.4	22.4	32.4	8
25	25	35	8
28	28	43	10
30	30	45	10
31.5	31.5	46.5	10
32	32	47	10
35	35	50	10
35.5	35.5	50.5	10
40	40	55	10
45	45	60	10
48	48	63	10
50	50	65	10
53	53	73	12
55	55	75	12
56	56	76	12
60	60	80	12
63	63	83	12
65	65	85	12
67	67	87	12
70	70	90	12
71	71	91	12
75	75	95	12
80	80	100	12
85	85	105	12
90	90	110	12
95	95	115	12
100	100	120	12
105	105	125	15
106	106	126	15
110	110	130	15
112	112	132	15
118	118	138	15
120	120	140	15
125	125	145	15
130	130	150	15
140	140	160	15
150	150	170	15

高性能PU素材（PU HOLLOW BAR FOR HYDRAULIC SEAL）

版權所有©久盛工業股份有限公司